








MRD600.1
| Brand | Rockville |
|---|---|
| SKU | MRD600.1 |
| Type | Marine and Powersports~Marine~Amplifiers |
| Variants | 1 |
The Rockville MRD600.1 is a mono Class D marine amplifier rated at 600 watts RMS at 1 ohm, dyno-tested at less than 1% THD. At 2 ohms it puts out 400 watts RMS and at 4 ohms 250 watts RMS — all verified numbers, not marketing estimates. The compact chassis measures 10.4" × 4.9" × 1.8", which means it fits under seats, inside consoles, and in tight bow storage areas where a conventional amp simply won’t go.
Marine construction starts with a conformal-coated PCB that seals the circuit board against moisture and salt. The chassis is UV and salt-resistant aluminum alloy, all hardware is stainless steel, and every terminal is sealed. White silicone covers with stretchy openings squeeze tightly around power, ground, remote, RCA, and bass remote cables individually, adding a secondary water barrier at each connection. Removable caps cover unused RCA inputs so nothing is exposed when ports aren’t in use.
The included metal bass remote has a clipping indicator that tells you in real time when you’re approaching distortion, so you can push output as far as the track allows without guessing. Remote level attenuation adjusts 0 to −26dB from the remote. The white remote cable and white amp chassis keep the install visually clean on boats where interior aesthetics matter.
Signal control covers the full range of subwoofer tuning. The bass boost sits at 45Hz (0–12dB) rather than the 80Hz center point common in budget amps — 45Hz targets actual low-frequency fundamentals rather than upper bass bloom. The low pass filter sweeps 50Hz to 200Hz, and the subsonic filter covers 10Hz to 50Hz to protect drivers from infrasonic content. Input sensitivity adjusts from 264mV to 8.0V on the low level input, and the 8V RCA preamp output supports daisy-chaining a second amp or subwoofer amplifier downstream via Tiffany-style RCA terminals.
Protection circuitry is fully IC-controlled with power, protect, and clip LED indicators on the front panel. A mute-and-delay soft start prevents turn-on transients. Battery operating range is 8V to 16.1V. Built-in fusing is 60A total via two 30A Maxi fuses. The amp runs true Class D — full-bridge topology — with a high-speed MOSFET power supply, a damping factor above 150 at 100Hz, and a signal-to-noise ratio of −91.9dBA per CEA 2006 measurement standards.
Specifications
- Type: Mono Class D marine amplifier
- RMS @ 1Ω: 600W (1% THD+N, 75% efficient) — dyno-certified
- RMS @ 2Ω: 400W (1% THD+N, 85% efficient) — dyno-certified
- RMS @ 4Ω: 250W (1% THD+N, 90% efficient) — dyno-certified
- Peak @ 1Ω: 2400W
- Peak @ 2Ω: 1600W
- Peak @ 4Ω: 1000W
- Frequency Response: 10Hz–200Hz
- Signal to Noise Ratio: −91.9dBA (A-weighted, CEA 2006)
- THD+N at Rated Power: ≤0.5%
- Damping Factor: >150 @ 100Hz
- Bass Boost: 0–12dB @ 45Hz
- Low Pass Filter: 50Hz–200Hz
- Subsonic Filter: 10Hz–50Hz
- Input Sensitivity: 264mV–8.0V
- RCA Preamp Output: 8V, Tiffany-style terminals
- Remote Level Attenuation: 0 to −26dB
- Power Supply: High-speed MOSFET
- Fuse Rating: 60A (2 × 30A Maxi, built-in)
- Power/Ground Terminals: 4 gauge
- Speaker Wire Terminals: 8 gauge
- Battery Voltage Range: 8V–16.1V
- Marine Protection: Conformal-coated PCB, UV/salt-resistant aluminum alloy chassis, sealed terminals, stainless hardware
- Dimensions: 10.4"L × 4.9"W × 1.8"H
In the Box
- MRD600.1 marine mono amplifier
- White metal bass remote with clipping indicator
- White remote cable
- White silicone terminal covers
- Removable caps for unused RCA terminals
Questions about this product
Is MRD600.1 in stock?
Yes — 48 units are available and ready to ship from our US warehouse.
How fast will MRD600.1 ship?
Orders placed before 3:00 PM ET ship the same business day. Delivery takes 3–5 business days inside the USA.
Where does MRD600.1 ship from?
It ships from the United States. Standard delivery is 3–5 business days, and orders placed before 3:00 PM ET go out the same day.